# Two DOA Pixelblazes?

**URL:** <https://forum.electromage.com/t/two-doa-pixelblazes/4767>\
**Category:** Troubleshooting\
**Created:** [September 23, 2026, 11:57am UTC](https://forum.electromage.com/t/two-doa-pixelblazes/4767 "2026-09-23T11:57:42Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Skydyvyr](https://forum.electromage.com/letter_avatar_proxy/v4/letter/s/ccd318/32.png) [@Skydyvyr](https://forum.electromage.com/u/Skydyvyr)\
**Post date:** [September 23, 2026, 11:57am UTC](https://forum.electromage.com/t/two-doa-pixelblazes/4767/1 "2026-09-23T11:57:42Z")

</div>

![IMG_4926](https://forum.electromage.com/uploads/default/original/2X/4/4a3f1456f9a424a582e866e5a3e7891039b37df1.jpeg)

I can’t believe I received two defective pixelblaze units, but I’ve wired them both up, verified that they are receiving 4.66vdc, but they don’t light up. Can you see anything wrong with my setup? Here’s the details:

12vdc/60w transformer —\> 12vdc sk6812 —\> electromage voltage reducer (12vdc to 5vdc putting out 4.66vdc) —\> pixelblaze controller.

Powering it up gets me no light on the board and no WiFi. Holding the reset button has no apparent effect.

I have two units and both are behaving the same way, which doesn’t make sense to me.

---

<div class="post-metadata">

**Author:** ![wizard](https://forum.electromage.com/user_avatar/forum.electromage.com/wizard/32/4_2.png) [@wizard](https://forum.electromage.com/u/wizard)\
**Post date:** [September 23, 2026, 12:00pm UTC](https://forum.electromage.com/t/two-doa-pixelblazes/4767/2 "2026-09-23T12:00:13Z")

</div>

Try disconnecting from everything and powering over usb.

4.6v is suspicious, the mini buck outputs 5v.

---

<div class="post-metadata">

**Author:** ![G6eorge](https://forum.electromage.com/user_avatar/forum.electromage.com/g6eorge/32/4135_2.png) [@G6eorge](https://forum.electromage.com/u/G6eorge)\
**Post date:** [September 24, 2026, 11:39am UTC](https://forum.electromage.com/t/two-doa-pixelblazes/4767/3 "2026-09-24T11:39:35Z")

</div>

What if you power the 5V regulator directly from the 12V supply. i.e. not going through the length of the LED Strip.

Also - what voltage is present on the ‘IN’ to the voltage regulator.

For info - Not saying it’s impossible, but I’ve never had a DOA Pixelblaze, been very reliable over many units. I have however broken a few of the electromage voltage regs (my fault!) by ripping resistors off.

As wizard says. start right from the beginning with a bare PB powered from USB and iterate from there.

---

<div class="post-metadata">

**Author:** ![davidseward](https://forum.electromage.com/letter_avatar_proxy/v4/letter/d/eb8c5e/32.png) [@davidseward](https://forum.electromage.com/u/davidseward)\
**Post date:** [November 13, 2026, 12:57am UTC](https://forum.electromage.com/t/two-doa-pixelblazes/4767/4 "2026-11-13T00:57:55Z")

</div>

Start with the bare USB test wizard suggested; that isolates the buck and strip wiring. If it still won’t boot on USB, the 4.66 V rail isn’t the only suspect. If it does boot, measure the reducer output both unloaded and at the Pixelblaze terminals. A reducer that reads ~4.66 V with no load is suspect; one that reads ~5 V unloaded but drops to 4.66 V when the strip is connected points to current draw or voltage drop in the 12 V feed or strip. Also double-check the 5 V output polarity before reconnecting.
